563-79-1 - Names and IdentifiersName2,3-Dimethyl-2-buteneSynonymsBISOMER DMB 2Tetramethylethene
Courriel : info@standard-groups.com
| Nom | 2,3-Dimethyl-2-butene |
| Synonymes | BISOMER DMB 2 Tetramethylethene Tetramethylethylene TETRAMETHYLETHYLENE 2,3-Dimethylbutene-2 2,3-Dimethyl-2-butene 2,3-DIMETHYL-2-BUTENE 2,3-Dimethylbut-2-ene 2,3-dimethyl-but-2-ene 2,3-DIMETHYL-2-BUTENE, STAB. 2,3-DIMETHYL-2-BUTENE, 1.0M SOLUTION IN TETRAHYDROFURAN |
| CAS | 563-79-1 |
| EINECS | 209-263-8 |
| InChI | InChI=1/C6H12/c1-5(2)6(3)4/h1-4H3 |
| Formule moléculaire | C6H12 |
| Masse molaire | 84.16 |
| Densité | 0.708 g/mL at 25 °C (lit.) |
| Point de fusion | -75 °C (lit.) |
| point Boling | 73 °C (lit.) |
| Point d'éclair | 2°F |
| Solubilité dans l'eau | Soluble in water (0.071 g/L) |
| Solubilité | 0.071g/l |
| pression vapeur | 215 mm Hg ( 37.7 °C) |
| Apparence | Liquide |
| Gravité spécifique | 0.708 |
| Couleur | Clear colorless to slightly yellow |
| BRN | 1361357 |
| Condition de stockage | 2 - 8 degrés Celsius |
| Stabilité | Stable. Highly flammable - readily forms explosive mixtures with air. Note low flash point. Incompatible with strong acids, strong oxidizing agents, peroxy compounds. |
| Sensible | Sensible à l'air |
| Limite explosive | 1.2%(V) |
| Indice de réfraction | n20/D 1.412(lit.) |
| Propriétés physiques et chimiques | Tetramethyl ethylene is an opaque liquid, M.P.-75 ℃, B. P. 73 ℃,n20D 1.4120, relative density 0.708,f. P. 2 F (-16 C), easy to burn, long-term contact with air is easy to be oxidized, insoluble in water, soluble in benzene, toluene, ethanol and other organic solvents. |
| Utilisation | For the production of chrysanthemum acid, spices |
| Codes de risque | R11 - hautement inflammable R65 - Harmful: May cause lung damage if swallowed R36/37/38 - Irritant pour les yeux, le système respiratoire et la peau. R22 - nocif si avalé R19 - May form explosive peroxides R40 - Limited evidence of a carcinogenic effect R36/37 - Irritating to eyes and respiratory system. |
| Description de la sécurité | S16 - Éloigner les sources d'allumage. S33 - Take precautionary measures against static discharges. S62 - If swallowed, do not induce vomitting; seek medical advice immediately and show this container or label. S9 - Keep container in a well-ventilated place. S36 / 37 / 39 - porter des vêtements de protection appropriés, des gants et une protection oculaire / faciale. S26 - En cas de contact avec les yeux, rincer immédiatement avec beaucoup d'eau et consulter un médecin. S36 / 37 - porter des vêtements et des gants de protection appropriés. |
| Un id | UN 3295 3/PG 2 |
| Wgk Allemagne | 3 |
| Code F de la marque Fluka | 10-23 |
| TSCA | Oui |
| Code SH | 29012980 |
| Note de danger | Extremely Flammable/Corrosive/Harmful |
| Classe de danger | 3 |
| Catégorie d'emballage | II |
| Introduction | 2, 3-dimethyl-2-butene is a hydrocarbon organic substance and can be used as an intermediate for pesticides and fragrances. At the same time, it is also used for the production of spices and other agricultural chemicals, especially the use of it instead of new hexene to produce tona musk spices, which has the advantages of low cost and stable product quality. |
| Utilisation | Tetramethylethylene, namely 2,3-dimethylbutene-2, is an intermediate of pyrethroid fenpropathrin. The intermediate of pesticides and spices is the main raw material for the synthesis of chrysanthemum acid. At the same time, it is also used for the production of spices and other agricultural chemicals, especially the use of it instead of new hexene to produce tona musk spices, which has the advantages of low cost and stable product quality. the raw material of agrochemical cyanuric acid pharmaceutical intermediates, used in the production of new diabetic drugs naglide used in the production of chrysanthemum acid and spices |
| Méthode de production | tetramethyl ethylene is obtained by dimerization of propylene. propylene is put into a dimerization kettle, a homogeneous catalyst is added, and catalytic polymerization is carried out under stirring. when the pressure in the kettle drops below 0.01MPa, the reaction of the material is stopped and the oil layer is crude steamed, remove the products of trimer and tetramer, namely C9 ~ C19. Olefins, collect the fraction at 53~75 ℃ as a crude product, which is mainly 2, 3-dimethylbutene-1, and then carry out catalytic isomerization, the reaction temperature is controlled at 85~90 ℃, so that the product is transformed into 2, 3-dimethylbutene-2, namely tetramethylbutene-2, and then carry out rectification to collect the fraction at 71~74 ℃, namely the finished product 2, 3-Dimethylbutene-2, the rest are other by-products C6 olefins. In the dimerization reaction, the one-way conversion rate of propylene is> 90%, the dimerization selectivity is 80%, and the isomerization conversion rate is 79%. |
| Température d'auto - inflammation | 754 °F |
Disclaimer: Le contenu ci-dessus est destiné à des fins de référence et de communication uniquement entre les initiés de l'industrie, et ne garantit pas son exactitude ou son exhaustivité. Conformément aux lois et règlements pertinents et aux règlements de ce site Web, les unités ou personnes qui achètent des articles connexes doivent obtenir des qualifications et des conditions de qualification valides.
Téléphone de l'entreprise
+86-21-6420 0566
Heures de travail
Du lundi au vendredi
Téléphone portable:
13816217984
Courriel :
info@qinsun-lab.com
